CrownChikk Posted January 30, 2024 Share Posted January 30, 2024 Greetings everyone, I had anticipated making more progress than what has been achieved so far. The user's text consists of a laughing face emoji. I have perused the available threads on the removal of the trim behind the glovebox, however it seems that the process may vary significantly for the Gen 1 facelift model. There is no screw that has to be removed from the side trim, and there are no screws present in the glovebox. I have removed all the screws below and can lower the trim at the rear by around 3-4 inches. However, I have encountered at least 2-3 clips that are producing a loud and unpleasant sound when pulled farther. Assistance in any kind would be very appreciated. I need to replace the parking sensor buzzer and have decided to concurrently replace the pollen filters. Link to comment Share on other sites More sharing options...
CrownChikk Posted January 30, 2024 Author Share Posted January 30, 2024 Alright, I have made progress up to this point. I will thereafter publish a selection of photographs. Nevertheless, kindly refrain from informing me that the speaker is affixed to the rear of the vehicle via the trunk or bonnet. I am unable to locate any nuts or screws on this side. This is obstructing the process of replacing the filters. I am completely unaware of the location of the parking sensor buzzer. Correction: I have located the buzzer. The component is positioned high above, located below the fresh air vent ducting for the passengers. Link to comment Share on other sites More sharing options...
CrownChikk Posted January 30, 2024 Author Share Posted January 30, 2024 It seems like it is fastened from the rear. Profound delight 🤣 Link to comment Share on other sites More sharing options...
Barringer Posted January 30, 2024 Share Posted January 30, 2024 To completely remove the glove box, you need to take out the felt trim piece, which is secured by many screws located beneath it. Regarding the sub, it does has studs and 3 nuts on the other side of the firewall. To reach them, it is necessary to remove the trim pieces located under the hood and in the front trunk. Once you have completed all the aforementioned tasks, I highly recommend replacing the cabin air filter. Since you have already gone through most of the necessary steps, it would be efficient to address this maintenance chore while everything is already disassembled. Link to comment Share on other sites More sharing options...
CrownChikk Posted January 30, 2024 Author Share Posted January 30, 2024 I have started the process of disassembling the decorative moulding in the trunk. I am now anticipating the delivery of a Windscreen wiper puller, which is scheduled to come tomorrow. Once the trim is removed, are they readily accessible? Concerning the glovebox trim, there were no screws present in the glovebox of my 2014 Spyder that needed to be removed. Yet another excerpt from below. Peculiar. Do you believe the reason is due to it being a cosmetic procedure to enhance one's appearance? Link to comment Share on other sites More sharing options...
Shiyardit Posted January 30, 2024 Share Posted January 30, 2024 Exercise extreme caution while removing the wiper arms, as it is very susceptible to causing damage to the windscreens. Place a layer of padding around the rim of the glass and ensure that the arms of the puller are kept at a safe distance. Link to comment Share on other sites More sharing options...
Authorce Posted January 30, 2024 Share Posted January 30, 2024 After removing the wiper arms and top trim piece, it is advisable to create an aperture or add an access lid for the brake reservoir fluid. I installed an aluminium frame and carbon cover on my vehicle. However, I found it rather inconvenient to have to remove the whole front trunk, wipers, and trim pieces only to check fluid levels. Link to comment Share on other sites More sharing options...
CrownChikk Posted January 30, 2024 Author Share Posted January 30, 2024 Thank to everybody, really the wiper arms were somewhat challenging. I using a puller to extract the middle wiper arm... However, the puller tool was unable to fit under the trim on the side. A puller equipped with two "pincher" arms on each side is clearly necessary. The one I purchased just included a slot located at the bottom. Subsequently, I used a generous quantity of release oil and a substantial degree of oscillation. The automobile, which is approaching a decade in age, has annual maintenance at Audi. However, I must emphasise that the wiper arms have been untouched for a significant duration of time. They were firmly stuck and there was no indication of any lubrication present? I used silicone grease throughout the reinstallation process. Does Audi need to carefully remove the trim in order to inspect the braking fluid? Link to comment Share on other sites More sharing options...
Bleakerje Posted January 30, 2024 Share Posted January 30, 2024 I had a same problem while attempting to detach my wiper arms. I have recently created a distinct article on the puller that I ultimately acquired. You may want to have a look at it for future reference. Link to comment Share on other sites More sharing options...
CrownChikk Posted January 30, 2024 Author Share Posted January 30, 2024 Regarding the speaker screws, it is really convenient to have them located in such a favourable position. Positioned snugly beneath the windscreen wiper reservoir. Link to comment Share on other sites More sharing options...
CrownChikk Posted January 30, 2024 Author Share Posted January 30, 2024 Finally, during my attempt to replace the pollen filters, I encountered a delay in realising that Audi had intentionally positioned the dense wire harness beneath the pollen filter housing. Link to comment Share on other sites More sharing options...
CrownChikk Posted January 30, 2024 Author Share Posted January 30, 2024 I discovered that the only method of inserting them was by applying a forceful pull on the loom, causing it to disengage from its original position beneath the housing. It was effortlessly easy. Audi charges a fee of £400 in the United Kingdom for this service. I see the reason why finding it amusing 🤣🤣 Link to comment Share on other sites More sharing options...
CrownChikk Posted January 30, 2024 Author Share Posted January 30, 2024 The automobile has accumulated a mileage of 34,000 kilometres. As a spyder, I assumed that the air conditioning and heating would not be used often. Nevertheless, I was astounded by the dire need for their replacement. Link to comment Share on other sites More sharing options...
Barringer Posted January 30, 2024 Share Posted January 30, 2024 It is quite probable that this is the original filter. It is a challenging task, as you are aware, and Audi does not provide sufficient time for technicians to do it during a service, so they often neglect it. Link to comment Share on other sites More sharing options...
CrownChikk Posted January 30, 2024 Author Share Posted January 30, 2024 Afterward, I dedicated the remaining part of the day to thoroughly cleaning the area under the hood. Link to comment Share on other sites More sharing options...
CrownChikk Posted January 30, 2024 Author Share Posted January 30, 2024 Thank you Barringer, I will examine it! Link to comment Share on other sites More sharing options...
Barringer Posted January 30, 2024 Share Posted January 30, 2024 I modified the scuttle panel by adding a rubber bung obtained from eBay to cover the brake fluid reservoir, allowing for easier access. Link to comment Share on other sites More sharing options...
CrownChikk Posted January 30, 2024 Author Share Posted January 30, 2024 I appreciate the ingenious concept. 👍 Indeed, I received a recommendation from another member to engage in that activity. It is logical. I believe that my battery may need replacement in the near future, therefore to be honest, it is not a significant issue to remove it. I have lubricated the wiper spindles. For your information, it seems to be a 100mm soil pipe blanking cap. 🤣 Link to comment Share on other sites More sharing options...
Barringer Posted January 30, 2024 Share Posted January 30, 2024 Not entirely accurate, but quite close. I used a 76mm diameter version of this item, however I would certainly choose for a larger size if I were to repeat the process. Currently, I am experiencing persistent urges from my obsessive-compulsive disorder (OCD) to devise a method for aligning a bigger hole saw in the middle. However, I am currently fighting these urges. Link to comment Share on other sites More sharing options...
CrownChikk Posted January 30, 2024 Author Share Posted January 30, 2024 I have enlarged the holes after first cutting a smaller one. I enlarge the hole in a piece of wood or plastic to the necessary size and then fasten it securely. I then use it as a guide without the central drill inserted. Link to comment Share on other sites More sharing options...
Barringer Posted January 30, 2024 Share Posted January 30, 2024 Indeed, I had contemplated pursuing a similar course of action. Please refrain from providing me any more encouragement.😄 Link to comment Share on other sites More sharing options...
Insignia GS Line Forum
Insignia GS Line Forum
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now