Jump to content

All Activity

This stream auto-updates

  1. Past hour
  2. Amazon.co.uk : volvo ecu
  3. Amazon.co.uk : EZK module Volvo 940
  4. Amazon.co.uk : fuel pump
  5. Amazon.co.uk : radio suppression relay
  6. Amazon.co.uk : Volvo coil pack
  7. https://www.amazon.co.uk/s/?search-alias=aps&field-keywords=Volvo
  8. My 1997 Volvo 940 estate with the 2.3-liter red block engine is for sale. During my drive, the engine suddenly stopped responding, wouldn't turn over, and displayed no rev counter. I suspected a faulty crank position sensor (cps) and replaced it with a new one, but the problem persists. The voltage at the coil pack was zero, so I moved on to the radio suppression relay (RSR), where I found 12 volts at the plug but no current flowing through it. I opened the relay and connected the two ends, but the engine still won't start. I don't have any fuel pump priming. A pulse from the injector is not feeling Unread tacos Devoid of voltage at the coil I think the EZK module or the ECU might be to blame for all these problems happening at once; am I correct in this assumption, and would installing tuning chips solve the problem? The modules should not be replaced.
  9. Yesterday
  10. I have verified my vehicle's specifications from the time of purchase and searched for the wheel details online, which indicates that Range Rover employs Narvik Black for the wheels.
  11. It is conceivable that they are merely standard Gloss Black. What if it is not metallic?
  12. I can merely speculate that it will be Santorini black.
  13. Greetings to all, I have regrettably damaged my factory-fitted black alloys on a 2021 RR Evoque; could anyone provide guidance on the appropriate colour for their repair?
  14. I appreciate it; I also surmise that the plastic hose is stuck due to the vehicle's age (2008). I considered applying WD-40, but I did not contemplate it extensively, to be frank. I appreciate the link; I will attempt it again and assess my progress. If everything else fails, a visit to the garage is necessary.
  15. If my recollection serves me correctly, the clamp is released yet remains in its position. The age of the materials may have caused the rubber and plastic components to adhere; apply some WD40 or a similar lubricant at the junction of the two parts near the clamp. I believe you will subsequently execute a strong push backward to initiate movement, as demonstrated in the video. I recall it being cumbersome. I composed a brief summary at the time of completion.
  16. I am encountering some challenges with this segment of the procedure, so I hope you can elucidate something for me. At 2:17 in the video, the clamp is released, a task I have also accomplished with the same instrument. My enquiries are: Should the clamp be elevated after being released, or is it acceptable to leave it in place? The device seems to exert force while maintaining the clamp's position. At 2:31, I am unable to detach the airbox from the pipe at the clamp, regardless of my efforts. This prompts me to question if the clamp must be elevated or displaced prior to the removal of the airbox. I would be grateful for some elucidation on this matter, as I am having difficulty detaching the airbox from the pipe.
  17. This video effectively demonstrates the necessary steps to follow.
  18. http://shop.ebay.co.uk/?_nkw=air+intake+hose&mkevt=1&mkcid=1&mkrid=710-53481-19255-0&campid=5338181132&toolid=10001&customid=2518X1570512X5d360692026ac9d44d2d4803b5458677&subId2=15
  19. Greetings to all, I possess a Mercedes C180K that displays the fault code P0100 – Malfunction in the Mass or Volume Air Flow Sensor Circuit. At reduced velocities, the engine's revolutions vary marginally, and the vehicle appears to be experiencing surges. I intend to either clean or substitute the MAF sensor and examine the breather hoses concurrently, yet I am encountering difficulties in detaching the air box. I have adhered to the procedures demonstrated in various online tutorials: - Detached the air intake duct. - Detached all connectors, encompassing the ECU connector. - Removed the two E-Torx fasteners securing the air box. I comprehend that these are captive bolts and must be elevated out of the path. - Employed extended hose-clamp pliers to disengage the clamp on the air-box hose. It is my comprehension that the air box ought to be retracted and elevated. Nevertheless, regardless of my efforts, I am unable to detach the hose from the air box, even after loosening the clamp. I prefer not to exert excessive force and potentially damage the plastic. To my knowledge, the air box has remained intact, leading me to question if the hose has become adhered over time. Am I overlooking a procedure, or is there a secure method to liberate it? Any guidance would be valued.
  20. Gearbox mounts and engine mounts, along with the opinions of others; did you purchase from a dealership?It appears that it requires a return; do not be concerned about the five months either.
  21. Have you had the transfer box oil replaced? Additionally, inspect the joints and supports of the prop shafts.
  22. Absolutely, no problems whatsoever. The sizes are spot on. Immediate infant
  23. Is the tread depth on each tire about the same?
  1. Load more activity
×
×
  • Create New...